Alcohol Fueled Based Vortex
Our alcohol based VortexED ‘55’ has been engineered to naturally swirl without the use of any electronics. Both portable and safe to use indoors; it’s a brilliant alternative to any table-top candle. May be used for commercial or residential use.
Available Sizes | Cost | Material
All Glass Heat-Treated
Glass thickness Options - 3/16” -¼” - 3/8”-½”
Custom Sizes are available (Extra Charges Apply).
Additional Metals. Extra Charges Apply
- Stainless Steel
Additional Glass. Extra Charges Apply
- Reflective Chromium (As Shown Add $40 to Standard Cost)
- Available in several colors
- All Glass Heat-Treated Tinted
Click Here for Operating Instructions
Vortex Videos, "CLICK HERE"
<iframe src="https://player.vimeo.com/video/178983778" width="640" height="564" frameborder="0" allow="autoplay; fullscreen" allowfullscreen></iframe>
Or CLICK "HERE" for Vortex Videos, 7 Pages of Videos
Q & A
Q. There are two or three ‘flags’. I get that the solid one is for snuffing the flame but not sure about the second one with the hole in the center. It seems to tame the flame a bit but the arm sticking out of the glass doesn't make sense. Is the unit intended to be operated with the hole flag in place?
A. The flags with Holes are to lower the flame. The reason for the arm is so that you can insert the snuffer without coming close to the fire. Again Snuffers with holes make the flame smaller.
Q. Also, the IPA (isopropyl alcohol) we had at the house is 70%. I think IPA can be bought at 99% . Do you recommend one over the other?
A. 70% is fine and is usually costs less, anywhere from $1.50 to $.89 cents a quart. 99% can be more expensive and doesn't burn any better. However, you could switch to denaturized alcohol for your Vortexed55 and the flame will burn blue. Denaturized alcohol is available at Home Depot or Lowes for about $15.00 a gallon.
Q. Finally, how much alcohol should go the fuel container? Is there a level that should be maintained for optimum performance?
A. Typically filling the container about 80% is best. After a few burns, there will be water/hydrogen at the bottom of the cup, dispose of it. It will not burn.
- For older models - having a good pair of leather gloves to handle the reservoir cup when removing it is advisable.
- Keep a flat piece of stone, marble or any heat resistant shield between your Vortexed55 and the table surface.
- For tall and older models, Vortexed55's, using a pair of pliers to lift and lower the reservoir cup makes the job a lot easier, especially when re-inserting a full cup.
- ALWAYS make sure the fire is completely OUT before handling the reservoir cup.
- NEVER pour any flammable liquid onto a flame. Even vapors can ignite and create a very dangerous situation.
Generation-1 Vortexed 55 Gallery
Below a few pictures from the Palm Springs Street Fair, a pair of 24" VortexED 55's. The one with the black base is a powdered coated steel model and the other is an brushed Aluminum, both with Bronze reflective glass.
Below we showcase a Generation-1 Vortexed55 fire at Big Bear CA.
A custom 30" stainless steel Generation-1 VortexEd 55, with 16" x 16" x 30" weighted base of stainless steel.
18" High, in Copper. This was Custom, so please call in interested (909) 989-6129
30" High in Copper - custom please call (909) 989-6129
These Generation One VortexED 55's, again shot at the Village Fest in Palm Springs CA.
Here are few more photos of the original VortexED 55 models.
The next several pictures are of Gisella Hunter in Palm Springs. She had us install a Blue Green fireglass
, painted the interior a Copper Ruby
, then she topped it with:
The alcohol Vortex Fires are brand new! We are producing several sizes and types ranging from $150.00 to $250.00 and range in sizes from 12” to 30”. These are and were developed for indoor use! They can also be used indoors as well. We wil be offering these in sizes as small as 6" x 6" x 12" adn up to 10" x 10" x 30". Pricing will vary depending on materials and design.
Please leave your name, e-mail and or number and we can and or will contact you when we finish the details in the next few weeks.
The VortexED ‘55’ Fires are one of our newer inventions/ creations, which we can manufacture for most any application indoors or outdoors.
These Vortex Fires are naturally aspirated and there are no electronics involved. The flame that you see has been engineered to perform in this manner and fashion. These VortexED ‘55’ Fires are all custom built for each individual customer and manufacturing time is 4 to 8 weeks plus, depending on our workload at the time of order.
VortexED ‘55’ Enclosure from 6” x 6” x 12” to 12” x 12” x 30”, standard.
Different metals: stainless steel, copper, brass, etc. Extra charges will apply.
Dozens of colors in Reflective Chromium and Tinted Heat Treated Glass.
Alcohol Fuel is a standard application.
www.Moderustic.com or www.AquaticGlassel.com
9467 9th Street #D Rancho Cucamonga, California 91730
Phone 909 989 6129 Fax 909 944 3811
Ed Jaunzemis Ed@Moderustic.com or Jaunzemis@msn.com
Christy Collins Design in Chicago at the Dana Hotel at the Vertigo on the top floor!
Click Here to see the pictures!
Vertigo Sky Lounge
Andrei's Restaurant Vortex Fires
Click HERE or on the picture to see our new 60" Octagon Vortex Fire
Dr. David Desai Vortex Project
Click HERE or on the picture to see the project.
Click HERE or on the picture below to see all of the NorthStar pictures
Click HERE or on the pictures of the Ritz Carlton Vortex' at Amelia Island Florida to how these were built. See the Videos!
Ritz Carlton Vortex Florida from Edgar Jaunzemis on Vimeo.
Ritz Carlton Vortex Page
Our outdoor VORTEX Fires are made to order with several available metal and glass options. And can be fueled by either propane or natural gas. Price range from $800 - $1600. See The VORTEX Video! By Carl Herkes, just CLICK HERE!